Title: How to DIY your board Author: nobody Time: Jun 28 16:43:24
What tools and materials can be purchased from DIY fingerboards, and how can I teach them?
Title: How to DIY your board - design principles and tools Author: JAY
Time: Jul 3 00:40:59
How DIY fingerboard
Design Principles:
Here is the general practice of the fingerboard, but it does not include the Campus Board. Generally speaking, the board of directors of the board of directors feels that it should include several principles.
1. Be symmetrical about.
2. Since the fingerboard is usually vertical, the design of the handle should suggest that the minimum and the most difficult point should be placed at the bottom, from the bottom up, bigger and bigger, so that the elbow will not encounter during training. Hand point.
3. For each handle point, if using ordinary carpentry two-point nails (black) screws, it is recommended to have two screws. If you use two and a half or three-quarters nails and screws, you can use only one screw to fix it. To use a screw that you can buy, two-screws can be found in the usual wood construction line. Two-and-a-half-four-pin nails are often purchased at a screw shop. If you use two-point four-legged nails, then the drill will buy two and a half points. If you use two-and-a-half-four-pin nails, you need to buy three-point drill bits, which is more than half the number of screws, and so on.
Tool articles
Electric drill
2.3 points horn lock drill bit: The so-called horn lock drill name is used to drill the general wooden door installation horn used to go to the hardware line with the boss to say, he should understand, drill bit Taiwanese to say drill, otherwise the boss will not know you Say what? This type of drill is a bit like a trigeminal shape, with a special sharp point in the middle. The drill bit will be printed with a 9-word and screw-like thread. The drilled hole will have a big hole outside and a small hole in it. This is In order to put the screw gasket. This kind of drill was originally used for hand tools. When I bought it in Luodong, the owner would use me to cut off the tail of the drill with a hydraulic shear. If it is not cut, it will not be able to find the center point by putting it into the drill. The drill bit rotates irregularly, so before you buy it, ask the boss if there is any hydraulic shear available. When drilling, don't let the drill drilled to the cement or metal in the sharpest part of the drill, because the hardness of this drill is very low.
3.2 and a half of the woodworking drill (assuming you use the ordinary two-point four-legged screw), this drill is very long, it is also used for hand tools, also like the horn lock drill, to break the tail, this bit hardness is softer, Never drill into cement. This kind of drill drills wood, which is better than black iron drills.
4. The woodworking hammer is flat, so that it will not hurt the wood and screw lines.
5. A saw, if you borrowed a Jigsaw, it would be very easy.
6. Screwdriver, or Allen Wrench/ Hex Wrench
7. Chisel: This can be used to make wood handles.
8. A small planer: This can be used to trim the right angle wood, so that the wood is less hand-wound, more comfortable grasping.
Title: Re => How to DIY your board - Design principles and tools / Supplementary Author: JAY
Time: Jul 3 00:54:24
In the previous article, I was not clear enough about the 3-point horn lock drill bit. The correct one should be said to be a spacer used to put three-point screws. In fact, the hole drilled by this bit is about an inch (2.5 cm). In addition to the gasket, it can also be used as a single finger Pocket training. So if you are afraid of buying the wrong one, the best way is to bring a ruler to measure more insurance.
Title: Re => How DIY Fingerboard:
Author: JAY
Time: Jul 5 19:57:31
Timber articles:
1. The mainboard of the fingerboard depends on where you can put the wood. Assuming that the most common place is at the top of the door, the width is usually only 7 and 80 centimeters. It is advisable to go straight to the timber line to buy it. 3 feet * 4 inches * 4 points of the drawer board, this wood texture is hard, and the standardization of the standard, buy back will not have to saw. As for how high the height of the fingerboard should be, look at each person. If you want to have more layers of handles, buy a few more. Suggest that 3-5 blocks should be enough.
2. Chinese fir bar:
The general building materials line of Chinese fir is usually called angled material (Taiyu pronunciation), usually two sizes of 1.8*1.2 inches or 1*0.8 inches, and the length is usually 8 feet and there are also 10 to 12 feet. It is recommended to use 1.8*1.2 inch size, because the 1.8-inch side is used to drill the hole and the screw area is large enough not to crack. The 1.2-inch side is used to grasp, about the length of the first knuckle, for the finger force. The exercises are very helpful. Because of the rough wood, it is recommended to use a coarse sandpaper to grind and grind it. The principle of not sticking to the hand is the principle. The right-angled part is to be repaired with a planer blade to be comfortable.
3. Positive semi-circular wood:
The so-called semi-circular wood, as the name implies, is a semi-circular wood strip, and there are many specifications. The most common ones are from 1 inch, 1.2 inch, 1.5 inch and 1.8 inch, and the length is 8 feet. Different materials have different prices, you can buy the most common white, do not have to buy beautiful lines of material. In fact, there are not only semi-circular but also some semi-oval wood strips, which is also very good for use as will be explained later in the production of hand grips.
4. Round sticks:
In the wood building line you can buy some round wooden sticks, there are many sizes, if you can, a 2.5-inch stick, it will be a good Open-handed handle points.
5. 1 inch white wood
This kind of wood is more expensive than Chinese fir, but there are several advantages. The first is that the softer texture can use wire saws, chisels, planers and even sandpaper to make some handy changes. Second, the 1-inch space is probably a little smaller than the length of our first knuckle. To increase the strength of the first knuckle, it is very convenient to use this type of wood training. This type of wood is also suitable for Campus Board. Hand point.
Title: Re => How to DIY your board Author: JAY
Time: Jul 7 20:17:52
How to make a fingerboard
Put a 3 foot drawer board piece by piece. If you want to make 5 layers, then arrange 5 pieces of board. Each piece of board will be locked on fir wood with 4 nails to form the main board of the board. It is advisable to use about 4 to 5 cedar strips. It is best to use one wood strip on each side (along the edges) of the wood chips. The rest is evenly placed so that the board will not be shaken or unstable during use. Case.
Arrange handle points
After the fingerboard is done well, it is necessary to consider how to arrange hand points. The principle has been mentioned before as symmetry, and from the bottom up, it is small and large. The reasons for symmetry should be solved. From the bottom up, we should be small and large. Apart from avoiding the elbow, I think another reason is safety, because it is easier to use small dots to fall without power and put it. The lower level is lower and safer. The above points are big, and even if you don't have the ability to do it, you'll be safer.
Fixed on the wall
If you only use it as a pure fingerboard, you can use two two-and-a-half geckos on the wall. If it is possible to use it as a Campus Board, it is advisable to use more than four fixed geckos. There are many types of geckos, and it is recommended to use a bullet that comes in from the end of a gecko. The first is that the price is cheap, and the second is that if the gecko wants to tear down or change the design, the gecko can be Remove the wall (take out the hammer with a hammer and knock it up and down to knock it out). The hole in the wall can be filled with a patch of soil and it is more convenient to restore the original shape.
How to make a handle
In fact, the handle points can be divided into three categories. The first is the right hand point, the second is the concave handle point, the third is the arc-shaped handle point, so use the previously introduced wood to do handle points.
1. Awkward training
First, it is recommended that the bottom board of the chip be set along the bottom edge of each side with a 1 inch or 1.2 inch semi-circular wooden bar. The purpose of this is to train the use of plutonium, especially the thumb and the tiger's mouth. For training, these two are often ignored. The training method is to place the four fingers of the two hands from the index finger to the little finger on the inside of the board, and put the thumb on the outside. The rotation of the palm toward the center line of the body can be used to pull Dan Gong. It may feel a bit difficult at first. You can grab the other hand first. Hand to do it.
2.1 inch white wood
This kind of wood is soft and can be ground at right angles with a planer or sandpaper and can be placed on the first layer of wood chips. If you match a 3 foot piece of wood and put a 3 foot long, 1 inch white wood, you can use a chisel to chisel a small hole or a concave point in some places so that you can train different ways of grasping.
3. Positive half-round wood
A. The first way to do the handle point of the semicircular wood, you can turn the arc surface inward (main board), plane outwards (to yourself), place the corners with a sandpaper, and then you will form a concave shape. The hand point, it is recommended to use more than 1.5 inches of semi-circular white wood is better, because the screw area is relatively large, more convenient.
B. The second kind can combine two pieces of equal length semicircular wood together to form a circular arc shaped handle point, and then use a horn to lock the drill bit on the outer side of the wood piece to drill a 1 inch round hole and rely on the positive of the main board. The semicircular wood uses a common drill to drill a hole that holds a screw. Two semicircular woods are nailed together with two nails to form a round stick-shaped hand point. It is suitable for training Open-handed grips and is less likely to hurt. Fingers. This hand point suggests a positive semicircle of 1.5 inches or more. If the half circle is thick enough, this hand point can also be used on Overhangihng and the ceiling, which is very cheap compared to buying a large handle. . . . many.
C. The third is to combine the positive semi-circle with the fir bar, and the fir bar is 1.8*1.2 inches, so the positive semi-circular wood uses 1.8 inches, but in fact the semi-circular wood is slightly larger than the 1.8 inch fir bar. The method is the same as the above one. It is to drill a hole in the semi-circular wood with a horn, and drill a screw hole in the fir bar, and the two are nailed together. Due to the large semicircle, when combined together, one side will slightly protrude a little bit, and on the other side will form a circular arc hand point.
4.1.8*.1.2 inch fir
A. The 1.2-inch side of this wood bar is a good handle point. If you saw the bar as a square or a 1 to 2 rectangle, the hand used to make the fingerboard is very good. Even on his Home Wall's 30 Degree Over-hanging, it feels very good. This kind of wood is generally very rough. It is recommended to use a sand mill to grind to the surface without protruding wooden pricks, but it does not need to be as smooth as the semi-circular white wood machine polishing, because it is slightly rough. During training or climbing, especially on over-hanging, the hand feels a lot like natural stone.
B. If you think that the 1.2-inch hand is too small, it is recommended that you can combine two pieces of 1.8*1.2-inch fir wood to become a big hand.
5. Round stick
In the construction material line, some round wooden sticks can be purchased for about several hundred yuan. Depending on the size of the purchased diameter, I have bought a 2.5-inch*8-foot round stick for about 350 yuan, which can be sawn in more than 16 stages. The size of each hand is approximately 3 cm or more longer than the width of our hand. This kind of big hand is suitable for fingerboards,
On the Campus Board, Over-hanging, and ceiling, if you want to buy a large block of Nicros, one price will be about 300 yuan.
What tools and materials can be purchased from DIY fingerboards, and how can I teach them?
Title: How to DIY your board - design principles and tools Author: JAY
Time: Jul 3 00:40:59
How DIY fingerboard
Design Principles:
Here is the general practice of the fingerboard, but it does not include the Campus Board. Generally speaking, the board of directors of the board of directors feels that it should include several principles.
1. Be symmetrical about.
2. Since the fingerboard is usually vertical, the design of the handle should suggest that the minimum and the most difficult point should be placed at the bottom, from the bottom up, bigger and bigger, so that the elbow will not encounter during training. Hand point.
3. For each handle point, if using ordinary carpentry two-point nails (black) screws, it is recommended to have two screws. If you use two and a half or three-quarters nails and screws, you can use only one screw to fix it. To use a screw that you can buy, two-screws can be found in the usual wood construction line. Two-and-a-half-four-pin nails are often purchased at a screw shop. If you use two-point four-legged nails, then the drill will buy two and a half points. If you use two-and-a-half-four-pin nails, you need to buy three-point drill bits, which is more than half the number of screws, and so on.
Tool articles
Electric drill
2.3 points horn lock drill bit: The so-called horn lock drill name is used to drill the general wooden door installation horn used to go to the hardware line with the boss to say, he should understand, drill bit Taiwanese to say drill, otherwise the boss will not know you Say what? This type of drill is a bit like a trigeminal shape, with a special sharp point in the middle. The drill bit will be printed with a 9-word and screw-like thread. The drilled hole will have a big hole outside and a small hole in it. This is In order to put the screw gasket. This kind of drill was originally used for hand tools. When I bought it in Luodong, the owner would use me to cut off the tail of the drill with a hydraulic shear. If it is not cut, it will not be able to find the center point by putting it into the drill. The drill bit rotates irregularly, so before you buy it, ask the boss if there is any hydraulic shear available. When drilling, don't let the drill drilled to the cement or metal in the sharpest part of the drill, because the hardness of this drill is very low.
3.2 and a half of the woodworking drill (assuming you use the ordinary two-point four-legged screw), this drill is very long, it is also used for hand tools, also like the horn lock drill, to break the tail, this bit hardness is softer, Never drill into cement. This kind of drill drills wood, which is better than black iron drills.
4. The woodworking hammer is flat, so that it will not hurt the wood and screw lines.
5. A saw, if you borrowed a Jigsaw, it would be very easy.
6. Screwdriver, or Allen Wrench/ Hex Wrench
7. Chisel: This can be used to make wood handles.
8. A small planer: This can be used to trim the right angle wood, so that the wood is less hand-wound, more comfortable grasping.
Title: Re => How to DIY your board - Design principles and tools / Supplementary Author: JAY
Time: Jul 3 00:54:24
In the previous article, I was not clear enough about the 3-point horn lock drill bit. The correct one should be said to be a spacer used to put three-point screws. In fact, the hole drilled by this bit is about an inch (2.5 cm). In addition to the gasket, it can also be used as a single finger Pocket training. So if you are afraid of buying the wrong one, the best way is to bring a ruler to measure more insurance.
Title: Re => How DIY Fingerboard:
Author: JAY
Time: Jul 5 19:57:31
Timber articles:
1. The mainboard of the fingerboard depends on where you can put the wood. Assuming that the most common place is at the top of the door, the width is usually only 7 and 80 centimeters. It is advisable to go straight to the timber line to buy it. 3 feet * 4 inches * 4 points of the drawer board, this wood texture is hard, and the standardization of the standard, buy back will not have to saw. As for how high the height of the fingerboard should be, look at each person. If you want to have more layers of handles, buy a few more. Suggest that 3-5 blocks should be enough.
2. Chinese fir bar:
The general building materials line of Chinese fir is usually called angled material (Taiyu pronunciation), usually two sizes of 1.8*1.2 inches or 1*0.8 inches, and the length is usually 8 feet and there are also 10 to 12 feet. It is recommended to use 1.8*1.2 inch size, because the 1.8-inch side is used to drill the hole and the screw area is large enough not to crack. The 1.2-inch side is used to grasp, about the length of the first knuckle, for the finger force. The exercises are very helpful. Because of the rough wood, it is recommended to use a coarse sandpaper to grind and grind it. The principle of not sticking to the hand is the principle. The right-angled part is to be repaired with a planer blade to be comfortable.
3. Positive semi-circular wood:
The so-called semi-circular wood, as the name implies, is a semi-circular wood strip, and there are many specifications. The most common ones are from 1 inch, 1.2 inch, 1.5 inch and 1.8 inch, and the length is 8 feet. Different materials have different prices, you can buy the most common white, do not have to buy beautiful lines of material. In fact, there are not only semi-circular but also some semi-oval wood strips, which is also very good for use as will be explained later in the production of hand grips.
4. Round sticks:
In the wood building line you can buy some round wooden sticks, there are many sizes, if you can, a 2.5-inch stick, it will be a good Open-handed handle points.
5. 1 inch white wood
This kind of wood is more expensive than Chinese fir, but there are several advantages. The first is that the softer texture can use wire saws, chisels, planers and even sandpaper to make some handy changes. Second, the 1-inch space is probably a little smaller than the length of our first knuckle. To increase the strength of the first knuckle, it is very convenient to use this type of wood training. This type of wood is also suitable for Campus Board. Hand point.
Title: Re => How to DIY your board Author: JAY
Time: Jul 7 20:17:52
How to make a fingerboard
Put a 3 foot drawer board piece by piece. If you want to make 5 layers, then arrange 5 pieces of board. Each piece of board will be locked on fir wood with 4 nails to form the main board of the board. It is advisable to use about 4 to 5 cedar strips. It is best to use one wood strip on each side (along the edges) of the wood chips. The rest is evenly placed so that the board will not be shaken or unstable during use. Case.
Arrange handle points
After the fingerboard is done well, it is necessary to consider how to arrange hand points. The principle has been mentioned before as symmetry, and from the bottom up, it is small and large. The reasons for symmetry should be solved. From the bottom up, we should be small and large. Apart from avoiding the elbow, I think another reason is safety, because it is easier to use small dots to fall without power and put it. The lower level is lower and safer. The above points are big, and even if you don't have the ability to do it, you'll be safer.
Fixed on the wall
If you only use it as a pure fingerboard, you can use two two-and-a-half geckos on the wall. If it is possible to use it as a Campus Board, it is advisable to use more than four fixed geckos. There are many types of geckos, and it is recommended to use a bullet that comes in from the end of a gecko. The first is that the price is cheap, and the second is that if the gecko wants to tear down or change the design, the gecko can be Remove the wall (take out the hammer with a hammer and knock it up and down to knock it out). The hole in the wall can be filled with a patch of soil and it is more convenient to restore the original shape.
How to make a handle
In fact, the handle points can be divided into three categories. The first is the right hand point, the second is the concave handle point, the third is the arc-shaped handle point, so use the previously introduced wood to do handle points.
1. Awkward training
First, it is recommended that the bottom board of the chip be set along the bottom edge of each side with a 1 inch or 1.2 inch semi-circular wooden bar. The purpose of this is to train the use of plutonium, especially the thumb and the tiger's mouth. For training, these two are often ignored. The training method is to place the four fingers of the two hands from the index finger to the little finger on the inside of the board, and put the thumb on the outside. The rotation of the palm toward the center line of the body can be used to pull Dan Gong. It may feel a bit difficult at first. You can grab the other hand first. Hand to do it.
2.1 inch white wood
This kind of wood is soft and can be ground at right angles with a planer or sandpaper and can be placed on the first layer of wood chips. If you match a 3 foot piece of wood and put a 3 foot long, 1 inch white wood, you can use a chisel to chisel a small hole or a concave point in some places so that you can train different ways of grasping.
3. Positive half-round wood
A. The first way to do the handle point of the semicircular wood, you can turn the arc surface inward (main board), plane outwards (to yourself), place the corners with a sandpaper, and then you will form a concave shape. The hand point, it is recommended to use more than 1.5 inches of semi-circular white wood is better, because the screw area is relatively large, more convenient.
B. The second kind can combine two pieces of equal length semicircular wood together to form a circular arc shaped handle point, and then use a horn to lock the drill bit on the outer side of the wood piece to drill a 1 inch round hole and rely on the positive of the main board. The semicircular wood uses a common drill to drill a hole that holds a screw. Two semicircular woods are nailed together with two nails to form a round stick-shaped hand point. It is suitable for training Open-handed grips and is less likely to hurt. Fingers. This hand point suggests a positive semicircle of 1.5 inches or more. If the half circle is thick enough, this hand point can also be used on Overhangihng and the ceiling, which is very cheap compared to buying a large handle. . . . many.
C. The third is to combine the positive semi-circle with the fir bar, and the fir bar is 1.8*1.2 inches, so the positive semi-circular wood uses 1.8 inches, but in fact the semi-circular wood is slightly larger than the 1.8 inch fir bar. The method is the same as the above one. It is to drill a hole in the semi-circular wood with a horn, and drill a screw hole in the fir bar, and the two are nailed together. Due to the large semicircle, when combined together, one side will slightly protrude a little bit, and on the other side will form a circular arc hand point.
4.1.8*.1.2 inch fir
A. The 1.2-inch side of this wood bar is a good handle point. If you saw the bar as a square or a 1 to 2 rectangle, the hand used to make the fingerboard is very good. Even on his Home Wall's 30 Degree Over-hanging, it feels very good. This kind of wood is generally very rough. It is recommended to use a sand mill to grind to the surface without protruding wooden pricks, but it does not need to be as smooth as the semi-circular white wood machine polishing, because it is slightly rough. During training or climbing, especially on over-hanging, the hand feels a lot like natural stone.
B. If you think that the 1.2-inch hand is too small, it is recommended that you can combine two pieces of 1.8*1.2-inch fir wood to become a big hand.
5. Round stick
In the construction material line, some round wooden sticks can be purchased for about several hundred yuan. Depending on the size of the purchased diameter, I have bought a 2.5-inch*8-foot round stick for about 350 yuan, which can be sawn in more than 16 stages. The size of each hand is approximately 3 cm or more longer than the width of our hand. This kind of big hand is suitable for fingerboards,
On the Campus Board, Over-hanging, and ceiling, if you want to buy a large block of Nicros, one price will be about 300 yuan.
Flower Stand Series,Modern Flower Stand,Solid Wood Flower Stand,Antique Flower Stand
Hebei Rukai Furniture Co. , Ltd. , https://www.wyrukaifurniture.com