[China] as a whole wardrobe wardrobe network installation is good or bad has a very important impact on the life of the closet, whole wardrobe closet installation also shows a company's degree of specialization, in general, then install the whole wardrobe is a whole wardrobe of corporate training Professional installation is better.
The overall wardrobe production process is different from the general purchase of panel furniture. First, the designer will have a close contact and communication with the user, understand the user's hobbies and their home style, and then measure the door to design a reasonable overall wardrobe. During this period, the designer will provide a computer rendering, and after the user is satisfied, the overall wardrobe will be made from the assembly line according to the drawings.
Overall wardrobe installation tools: Power tools: charging batch, impact drill, jig saw, polishing machine, angle grinder
Hand tool for whole wardrobe installation: hole opener, level ruler, glass glue gun, tape measure, square ruler, hammer
Overall wardrobe installation steps:
One: cabinet installation
1. Use a cloth to pad the floor, first assemble from the wide side plate at one end of the wall, and lay the wide side plate on the ground, keeping a distance of 600mm from the back wall. First, fill the three-in-one rubber plug plate flat on the cloth, check the hole spacing and the drawing, and install the three-in-one single-link. Focus on the product structure, all the fixed positions of the horizontal and vertical intersections are three-in-one connection, the three-in-one mast is mounted on the embedded part of the phase plate, and the depth of the rubber is applied to the lower part of the mast.
2. In principle, the assembly is carried out in the middle, and each of the plates is wrapped with a mast hole and an eccentric wheel hole, and the mast-mounted plate member is aligned with the mast on the corresponding plate member. Insert the hole into the hole, and the mast head can be seen about 5.5mm from the eccentric wheel hole. Then insert the eccentric into the hole. (When installing the eccentric, note that there is an arrow on the surface of the eccentric to indicate the direction to be aligned with the mast. Hole), turn clockwise and tighten so that the two intersecting plates can be fastened.
3. In the assembly process, the assembly is carried out with the face facing down and facing upwards. If there is a blank position in front of the cabinet body, the internal structure should be installed first, and the item below the height of the front left position should be placed on the bottom surface. (Generally use the cabinet footboard or the closing plate), then assemble the outer panel and finally install the cabinet foot.
Two: backplane installation
1. After the cabinet body is assembled, draw the center line for the back panel assembly for the intersecting panels. There are two ways to fix the backplane with a normal peripheral board:
a. Half-slot; half-slot means that a 7-shaped notch is opened on the inner side of the rear side of the peripheral plate, and the back plate is placed on the half-slot and fixed by nails or wires.
The b-shaped groove is formed by leaving a plurality of positions on the inner side of the rear side of the peripheral plate, and the back plate is inserted into the notch and clamped and fixed by both sides of the groove.
2. When assembling the backboard, the angle of the cabinet must be righted first. In the case where the ground level is relatively horizontal, the most common method is to use the steel ring to measure the diagonal of the cabinet. According to the drawing structure, put the backboard on the back of the cabinet (because the seam of the backboard will be docked to the corresponding centerline of the corresponding panel at the time of production), then insert the backboards on both sides into the back of the two sides. Inside the plate slot, put the middle back plate. Fix the center line according to the original backing plate, extend it to the corresponding position on the back plate, and drill a hole in the fixed position of the back plate screw with a 3.5mm twist drill to prevent it from loading. When the screw is broken, the cabinet body plate is broken. When the two backing sheets are seamed together, a 3.5mm drill can be used to align the holes between the two backing plates, and then screwed between the two backs.
Box Facial Paper, Soft Box Facial Paper,Sanitary Box Facial Paper,Sanitary Facial Tissue
BODA ENTERPRISE LIMITED , https://www.bodapaper.com